6800W 4-Channel Amplifier with NomadLink Network Monitoring and Dedicated Control for Install Applications
C SERIES C 68:4
The C 68:4 Delivers 4 × 1700 W at 4 OHMS, Making This Amplifier Powerful Enough for the Vast Majority of Demanding Installed Sound Applications.
The C 68:4 delivers 4 × 1700 W at 4 ohms, making this amplifier powerful enough for the vast majority of demanding installed sound applications. Packaged in a compact 2U chassis, the C 68:4 sets a new standard for high power in an installation-dedicated amplifier.
C Series amplifiers are uniquely capable of adapting to a wide variety of demanding load conditions. Each channel has an individually configurable Voltage Peak Limiter (VPL™), which allows the output to be optimized for any loudspeaker load – whether one massive subwoofer or a series of small 100/70 V loudspeakers. VPL works in combination with adjustable input gain to achieve maximum headroom regardless of input levels or output impedances.
Every C Series is ready for the NomadLink® network right out of the box. With NomadLink, key amplifier parameters are displayed via DeviceControl software, and remote control of channel mutes and power on/off is managed efficiently under network control.
General
| Number of amplifier channels |
4
|
| Peak total output all channels driven |
6800 W
|
| Peak output voltage per channel |
141 V
|
| Max output current per channel |
24.5 Arms
|
Max output power (all channels driven)
| 16 ohms |
650 W
|
| 8 ohms |
1200 W
|
| 4 ohms |
1700 W
|
| 2 ohms |
1200 W
|
| Hi-Z per ch. (all ch.’s driven): 70 Vrms / 100 V peak |
1600 W
|
Max output power bridged
| 16 ohms |
2400 W
|
| 8 ohms |
3400 W
|
| 4 ohms |
2400 W
|
| 2 ohms |
Not recommended 1
|
| Bridged per ch.: 140 Vrms / 200 V peak |
3200 W
|
Performance
| THD 20 Hz - 20 kHz at 1 W |
<0.1%
|
| THD at 1 kHz and 1 dB below clipping |
<0.05%
|
| Signal to Noise Ratio |
>112 dBA
|
| Channel separation (Crosstalk) at 1 kHz |
>70 dB
|
| Frequency response (1 W into 8 ohms) + 0 / -3 dB |
6.8 Hz - 34 kHz
|
| Input impedance |
20 kOhm
|
| Common Mode Rejection (CMR) |
>50 dB, 20 Hz - 20 kHz
|
| Output impedance @ 100 Hz |
30 mOhm
|
Gain, Sensitivity and Limiters
| VPL, selectable per ch 2 |
141, 118, 100, 85, 71, 59, 50, 42 V
|
| VPL, when bridged 2 3 |
282, 236, 200, 170, 142, 118, 100, 84 V
|
| Voltage Peak Limiter mode (per ch.) |
Hard / Soft
|
| Amplifier gain selectable (all channels) – rear-panel switches 3 |
23, 26, 29, 32, 35, 38, 41, 44 dB
|
| Default gain |
35 dB
|
| Level adjustment (per channel) |
Front-panel potentiometer, 21 position detented from -inf to
|
Connectors and Buttons
| Input connectors (per ch.) |
3-pin Phoenix, electronically balanced
|
| Output connectors (per ch.) |
Barrier strip 2-pole screw terminals
|
| Output bridge mode |
A+B and/or C+D, inputs A and C are input source
|
| NomadLink network |
On board, 2 x RJ45 connectors IN and OUT
|
| Intelligent fans (on/off) |
Yes, depending on presence of output signal
|
| Power |
Individual switches on front panel
|
| Cooling |
Two fans, front-rear airflow, temperature controlled speed
|
Front-panel user interface
| Common |
NomadLink Network; Power Average Limiter (PAL)5; Power on
|
| Per channel |
Signal present / High-impedance; -10 dB and -4 dB output signal;Voltage Peak Limiter (VPL); Current Peak Limiter (CPL): Very High Frequency (VHF); High temperature; Fault; Mute
|
Power
| Operating voltage, 230 V / 115 V nominal |
130-265 V / 65 -135 V 4
|
| Minimum power-up voltage, 230 V / 115 V |
171 V / 85 V
|
| Power Average Limiter (PAL) 5 |
Yes
|
| Power Factor Correction (PFC) |
No
|
| Soft-start / Inrush Current Draw |
Yes / max. 5 A
|
| Mains connector |
230 V CE: 16 A, CEE7; 115 V ETL: 20 A / NEMA 5-20P; C16:4: 15A/NEMA 5-15P
|
Dimensions
| Dimensions |
W: 483 mm (19”), H: 88 mm (2 U), D: 343 mm (13.5”)
|
Weight
Finish
| Finish |
Black painted steel chassis with gray painted steel front
|
Approvals
| Approvals |
CE, ANSI/UL 60065 (ETL), CSA C22.2 NO. 60065, FCC
|
