The headphone amplifier and monitoring controller with 120V technology
Phonitor 2 is the ultimate headphone amplifier and monitoring controller with 120V technology for demanding sound and mastering engineers. The Phonitor Matrix enables mixing and mastering on headphones in the highest quality – just like on loudspeakers.
Great sound – for headphones
The Phonitor 2 offers connection for a standard headphone with a stereo jack plug on the front.
Thanks to the enormous output power, all headphones are driven effortlessly. Thus, it plays out the advantages of the SPL 120V technology and rewards the listener with an honest, detailed and at the same time vivid sound experience.
Great sound – also for loudspeakers
On the rear panel, the Phonitor 2 offers a stereo output which makes it a high-quality monitoring controller for any monitoring situation. Active speakers with an integrated power amplifier or passive speakers in combination with a power amplifier can be connected at this output.
Monitoring at the highest level
The signal quality of the Phonitor 2 offers the same quality as the big SPL DMC and MMC mastering consoles.
Headphones or Speakers
The OUTPUT switch – simply switch from headphone to speaker playback.
In the center position (Mute), no signal reaches the outputs. The VU meters light up red.
With a dip switch on the bottom of the device, the volume control for the rear stereo output can be switched out of the signal path.
Would you like a little bit more?
The SPL Expansion Rack is not only a 19” rack housing for the Phonitor 2, it also expands the connection possibilities.
A passive four-way switch integrated into the Expansion Rack allows the Phonitor 2 speaker output signal to be switched between up to four stereo speaker pairs.
On the input side, three stereo analog inputs are offered.
XLR inputs 1 and 2 are optimal for connecting balanced sources, such as for example a high quality DA converter or audio interface.
RCA input 3 is perfect for connecting, for example, a CD player or other similar sources with RCA outputs.
When a CD player or other hi-fi equipment is connected to the RCA jacks, the consumer level can be increased from -10 dBV to 0 dBu with a dip switch on the bottom of the device. In this way, the sources are better comparable in terms of their level.
Milled from solid
The massive 45mm volume control knob milled from aluminum is a haptic highlight. Its mass together with the motorized Alps RK27 “Big Blue” potentiometer enhances the “spoon in the honey” feeling even further and provides perfect control of the monitoring level.
The volume control can be remotely controlled with any infrared remote control.
The Phonitor 2 learns to communicate with it with the simple push of a button.
Monitoring without any compromises
The Phonitor 2 is a full-fledged monitor controller:
- Sources: 2x XLR, 1x RCA
- Solo L/R
- Phase inversion for L and R
- Output switchable to headphones or speakers
- Phonitor Matrix with Crossfeed, Speaker Angle and Center Level (the latter can be switched off)
- Laterality control
Finding the real center
Naturally, hearing can be directed more to the left or more to the right. This becomes particularly clear when listening on headphones.
Therefore, the Phonitor 2 has the uniquely finely resolved laterality control,
which rebalances the stereo image on the monitoring side.
The Mono/Stereo switch not only selects between stereo or mono playback.
This switch also activates the laterality control.
M/S – Center or Side?
By using the mono/stereo and L/R phase inversion switch in combination, it is also possible to only monitor the center or side signal. When the switch is set to “Mono” and phase inversion is active for L (or R), only the side signal is played back. If the phase inversion is switched off, the mono signal corresponding to the “M” signal is played back. Separate monitoring of the M and S signals has become a widespread standard for many mixing and mastering engineers.
Everything at a glance
Two mechanical VU meters visualize the input levels for the left and right audio channels.
The “VU Cal” switch can be used to reduce the signal visualized on the VU meters by -6 dB or -12 dB.
Thus, the VU meters operate in the ideal display range even at very high input levels.