ADAM Audio A77X-Sub15 Bundle

SKU: ADAM A77X-Sub15 Bundle
$ 6,499.97 -15%
$ 5,499.97

The ADAM A77X-Sub15 Bundle is a 3.1, 4-way, matched system with a SUB15 15" subwoofer and two A77X dual-woofer monitors with X-Art ribbon tweeters.

ADAM Audio A77X

The A77X is a 2.5-way, horizontally oriented near/midfield monitor that features dual 7" woofers for separate bass and midrange, ADAM’s proprietary X-ART tweeter, a combined power output of 250 watts, and a frequency response of 38Hz to 50kHz

The multiple award-winning ADAM A77X is the culmination of all the innovative technology found in the AX series, plus a little extra. The unique feature of the A77X is found in the function of the two 7" woofers. Rather than simply dividing the bass and mids between them at two crossover points, both woofers act together from 38Hz to 400Hz, effectively doubling the speaker surface area for low frequencies. At 400Hz, one of the drivers fades out while the other handles the midrange from 400Hz to 3kHz. The advantage of this configuration is a significant amount of bass reproduction that obviates the need for a separate subwoofer and a clean, neutral sound in the all-important midrange, free from interference and phase cancellation. Naturally (which is a pretty good word for it), the high frequencies are handled by ADAM’s own X-ART folded ribbon tweeter, which extends the A77X frequency range up to 50kHz. the A77X is effective for nearfield and midfield monitoring.

ADAM Audio A77X—Just the Facts:

  • High-end dual woofer design made affordable
  • 2x 7" carbon/Rohacell®/glass fiber woofers
  • X-ART accelerated ribbon tweeter
  • 50W/2 x 100W amplification
  • Front-panel on/off switch and volume gain
  • Rear-panel tweeter gain and two room-compensation shelving filters
  • Frequency range from 38Hz to 50kHz
  • XLR and RCA connectors
  • 122dB max peak SPL per pair
  • 5-year warranty (2-year plus 3-year extended)
  • Package Contents: Two A77X active monitors with Sub15 subwoofer

ADAM Audio A77X—Behind the Grille

Dual-woofer design becomes affordable

In certain control rooms, it may be advisable to use a horizontally designed speaker rather than a vertical one. Until the introduction of the A77X, horizontally oriented monitors were only available in ADAM’s high-end SX series.

The game-changing is equipped with the same advanced technologies as the A7X, it, therefore, is very similar to the two-way speaker. The A77X, however, distinguishes itself by much higher, compression-free maximum sound pressure levels and dynamics. Due to its power and radiation characteristics, it also is perfectly suited for both near- and midfield monitoring.

Especially noteworthy of the A77X is the extremely wide stereo field and brilliant stereo imaging. Treble and mids are reproduced with three-dimensional realism and the lows are, as expected from a double woofer design, massive without compromising on precision.

X-ART folded ribbon tweeter technology

Like all models of the AX, the A77X features the ADAM proprietary X-ART tweeter. The “X” stands for “eXtended frequency response,” which is one of the features of Accelerating Ribbon Technology (ART) that has been drastically improved. It now extends all the way up to 50kHz. In addition, the X-ART tweeter has higher efficiency and higher maximum sound pressure levels.

How X-ART works

From its inception, ADAM Audio emerged as a major force to be reckoned with in pro audio monitoring, mainly due to its innovative folded ribbon tweeter. The ribbon tweeter is based on the Air Motion Transformer concept developed by Dr. Oskar Heil, which is a pleated diaphragm similar to the shape of bellows. From the standpoint of surface area response, a 1-inch-wide pleated diaphragm is comparable in function to an 8"-diameter cone. The folded driver acts like a point-source version of a larger driver, which inherently results in lower distortion during sound reproduction. Another property of the folded diaphragm is that its squeezing movement projects air with a speed approximately five times faster than the speed of the ribbon driver itself. 

ADAM engineers took this technology and improved on it, incorporating superior geometries and materials to achieve unprecedented audio fidelity. The latest iteration of the ADAM folded ribbon tweeter is the X-ART, which explores new paths in the kinematics of moving air, resulting in a dramatic improvement in the quality of audio reproduction.

The X-ART membrane consists of a pleated diaphragm in which the folds compress or expand according to the audio signal applied to them. The result is that air is drawn in and squeezed out, like the bellows of an accordion.

The ADAM X-ART design overcomes the piston-like motion of all conventional drivers and their inevitable problems, such as narrow directivity, by achieving an improvement in air loading by a factor of 4 over conventional transducers. In addition, the X-ART tweeter’s pleated membrane avoids the typical breakup/distortion and subsequent dynamic limiting at higher frequencies found in dome and cone tweeters. Another positive result of the X-ART design is that the driving “stripes” are in direct contact with the outer air and are cooled immediately.

Diaphragm area is another important factor in determining the dynamic range of a transducer. Basically, what you see is what you get. The cone area you can see is always the acoustically active area of the loudspeaker–this is true for practically all other drive units. By folding the X-ART diaphragm into the 3rd dimension (as seen from the listener’s position) a larger foil can be used, thus increasing the acoustically effective area of the diaphragm by a factor of more than 2.5 times. This results in a higher dynamic output with extremely wide dispersion.

ADAM driver technology

While ADAM driver technology could easily be misconstrued as the clone center that gave us Han Solo’s disappointing son, it actually refers to the A77X’s two 7" carbon/Rohacell/glass fiber composite woofers, which are identical to that of the A7X (maybe some cloning is involved after all). With their large voice coils (1.5") and powerful amplifiers, they are capable of very high sound pressure levels as well as very deep bass extension. Both 7” woofers work together from 38Hz up to 400Hz, at which point, one woofer fades out and only the second woofer continues to operate in the midrange up to 3 kHz. This prevents interference and possible phase cancellation in the critical midrange.

ADAM proprietary A/B and PWM amplifiers

Each driver has its own dedicated amplifier. A 50W A/B amp is responsible for the X-ART tweeter, while the bass and mid-woofers are each driven by a 100W PWM (pulse-width modulation amp.

Custom A/B amplifier

While the X-ART tweeter’s solved certain problems associated with conical tweeter designs, its wide bandwidth up to 50kHz, though responsible for the musicality and openness of the A77X’s high-frequency response, also created a problem in terms of amplification. PWM (pulse-width modulation) amplifiers, which have become popular due to their high power efficiency and low distortion, require a low-pass filter to separate the modulation frequency (the point where power switches from the supply rails) from the audio band. it imposes a limitation on the high-frequency reproduction of the X-ART tweeter. To preserve the wide bandwidth, which in turn preserves the phase coherency and resultant realism of audio in the audible range, ADAM put considerable time and effort into creating a high-frequency power amp to allow the high-frequency tweeter to live up to its potential.

An internal bandwidth of more than1MHz is externally limited so that the unit delivers an ultra-wide response up to 300kHz. With nothing limiting the abilities of the X-ART tweeter, the monitor has unsurpassed clarity and openness which will daze and amaze even the most jaded professional ear.

PWM custom amplifier

PWM (Pulse Width Modulation) also known as Class D amplification or switching amp technology (and mistakenly digital amplification), converts the incoming signal to a series of rectangular waveforms of equal height. The width of the rectangles varies in time and represents the musical signal. This waveform can be amplified much more simply, as the transistors are used as switches that only turn the power supply voltage on and off.

It is possible that a very fast mechanical switch could do the job, but power transistors are a better choice for the task, as such, PWM amplifiers work pretty much like conventional Class AB designs.

The main advantage of PWM amplifiers is their extremely high efficiency (>90%). As a consequence the heat to be dissipated is only one-fifth of earlier designs, leading to much lower temperatures within the amps and making the use of heat sinks unnecessary.

While PWM is highly efficient, pulse-width modulation causes signal distortion due to non-linearity of the modulation based on transient response. Usually, some form of noise-shaping filter is required to eliminate the distortion. However, that alone wasn’t good enough for ADAM engineers, who set out to develop PWM units that would perform at the leading edge of sonic quality while maintaining high efficiency. The ADAM units use a proprietary technology for both the amp and the power supply section (i.e. no more transformers) combined with state-of-the-art input and filter sections to achieve the best in multi-channel active monitoring.

A77X controls

The front panel includes a power switch and a control for the volume that retains the volume setting independently from the on/off switch. The rear panel features several additional controls: a gain for the high frequencies (± 4dB) and two shelf filters for high and low frequencies. To ensure greater compatibility, there are both XLR (balanced) and RCA (unbalanced) connectors.

ADAM Audio Sub15

The ADAM Audio Sub15 is an extremely powerful, 1000-watt, 15" subwoofer capable of extending the frequency range of main and midfield monitors down to 20Hz

If you spend a major concentration your time plumbing the depths of audio in bass-oriented music, such as hip-hop and R&B, or film post, where thunderous effects, orchestral score, and dialog have to peacefully co-exist, the powerful ADAM Sub15 gives you 1,000 watts of low-frequency extension down to 20Hz—great for large control rooms and equally large productions. The ADAM Sub15 features a sturdy 15" woofer made of an exceptionally rigid aluminum membrane. Why aluminum you ask? A 15-inch woofer has to overcome more inertia than smaller cones in order to respond quickly to transient information. The Sub15 is driven by two powerful magnets and a 4" (100 mm) voice coil. The Sub15’s inertia busting power assist comes from a highly efficient PWM (pulse-width modulation amplifier that pumps 1000 watts (RMS) of power into the Sub15’s driver with an efficiency factor of nearly 90%. With these performance features, the Sub15 is easily capable of handling critical musical passages with intense and sudden bass peaks without showing signs of distortion or overheating.

ADAM Audio Sub15—Just the Facts:

  • 5" subwoofer (aluminum)
  • Amplifier power RMS/Music, 1000W/1200W
  • Frequency response of 20Hz-150Hz
  • Maximum SPL 120dB
  • Additional sub output enables dual sub system

ADAM Audio Sub15—Behind the Grille

15" aluminum driver

The Sub15 combines excellent transient response capability, thanks to its light-weight aluminum driver, with impressive low-frequency performance to enable a genuinely musical reproduction experience. With a high and undistorted sound pressure output of 120dB maximum SPL at one meter (3 ft.), the Sub15 makes the perfect subwoofer for mid-sized and larger control rooms.

A downward-firing bass-reflex port has been specially designed with ample dimensions and rounded edges to cancel any port noise that could compromise playback. Best of all, with an ADAM Sub15 working in concert with your monitor system, you get all the low-frequency information you need to make informed mix decisions. Plus, if you do decide that you want to pin your clients to the back wall, you can.  

PWM custom amplifier

PWM (Pulse Width Modulation) also known as Class D amplification or switching amp technology, converts the incoming signal to a series of rectangular waveforms of equal height. The width of the rectangles varies in time and represents the musical signal. This waveform can be amplified much more simply, as the transistors are used as switches that only turn the power supply voltage on and off.

Advantages of PWM

The main advantage of PWM amplifiers is their extremely high efficiency (>90%). As a consequence the heat to be dissipated is only one-fifth of earlier designs, leading to much lower temperatures within the amps and making the use of heat sinks unnecessary. The ADAM units use a proprietary technology for both the amp and the power supply section (i.e. no more transformers) combined with state-of-the-art input and filter sections to achieve the best in multi-channel active monitoring.

Room-compensation controls and I/O

In order to adjust the sound of the Sub15 to different room situations or individual taste, the Sub15 has several controls including one for volume (-60dB to +6dB) and one for the crossover frequency (50Hz – 150Hz). The satellite speakers can either be driven full range or high-pass filtered at 85Hz. This allows the Sub15 to be easily integrated into a Dolby surround setup. Unfavorable phase relationships between the satellites and the subwoofer, particularly in the crossover frequency range, can be easily controlled with the rear-panel phase-reverse switch.

The Sub15 is also very flexible when it comes to connectivity: There are balanced (XLR) and unbalanced (RCA) Left/Right input/output connectors to be found on the rear of the subwoofer, plus an additional output enables a dual subwoofer array.

ADAM Audio Sub15 features and benefits:

Linear bass reproduction down to 20 Hz  

  • Optimal addition to midfield and main monitors

Maximum Peak sound pressure in 1 m ≥ 120dB  

  • Powerful, compression-free sound reproduction even at very high sound levels

High-efficiency PWM amplifier  

  • Low-distortion amplification at both low and high volume levels

Special 15" woofer with aluminum diaphragm  

  • Unrestricted bass reproduction for low-fatigue operation even at high volumes

Additional sub output  

  • Allows building a dual bass array

Downward working bass reflex tube with generous dimensions and corresponding rounding  

  • Prevention of air turbulence noise

Upper cut-off frequency is selectable between 50Hz-150 Hz  

  • Allows optimal adaptation of the total system on the bass performance of the satellites

Connectable high-pass filter for the satellite outputs, which blocks signals below 85Hz  

  • Dolby®—Fair reproduction of film sound
  • Disengages the satellites from the low frequencies

2-year warranty with an optional extension to 3 years with the registration of the product  

  • Full repair service if required for 5 years

If you're working in the sub basement of audio production and need extra low-frequency extension to effectively hear sub bass for EDM, hip hop, R&B, or other applications requiring accuracy and projection in the low frequencies, The A77X-Sub15 bundle is a superb choice. For more information, call or chat online with your PAD Studio Specialist today.  


A77X   

  • Tweeter: X-ART
  • Velocity transform ratio: 4:1
  • Equivalent diaphragm diameter: 2" / 56 mm
  • Woofer: 2x 7" / 175 mm
  • Woofer material: Carbon/Rohacell/glass fiber
  • LF amplifier: 2x 100W RMS/150W music, type PWM
  • HF amplifier: 2x 50W RMS/75W music, type A/B
  • Input sensitivity: -∞ to +14dB
  • Tweeter gain: ±4dB
  • High shelf EQ > 5kHz: ±6dB
  • Low shelf EQ < 300Hz: ±6dB
  • Frequency response: 38Hz – 50kHz
  • THD 90dB/1m>100Hz: ≤ 0.5%
  • SPL with sine wave 100Hz-3kHz in 1m: ≥ 114dB
  • peak acoustic output in 1m per pair: ≥ 122dB
  • Crossover frequency: 400Hz/3kHz
  • Input: XLR/RCA
  • Input impedance: 30k ohm
  • Magnetically shielded: N/A
  • Dimensions (HWD): 9.3" x 10.9" x11" (235 x 530 x 280 mm)
  • Weight: 28.2 lb. / 12.8 kg

Sub15

  • Subwoofer: 15" / 310 mm
  • Voice coil diameter: 4" / 100 mm
  • Woofer material: Aluminum
  • Built-in amplifiers: 1
  • Subwoofer channel 1/2: 1,000W/1,200W
  • Frequency response: 20Hz-150Hz
  • THD >60 Hz: ≤ 1%
  • Maximum peak: ≥ 120dB
  • Crossover frequency: 50Hz-150Hz
  • Inputs: XLR / RCA
  • Input impedance 100k ohm
  • Weight 114 lb. / 52 kg
  • Dimensions (H x W x D): 25" x 18-1/2" x 21" / 635 x 470 x 525 mm
  • Warranty: 2 years with 3 years optional extension
JUST SEEN

Search

Just added to your cart:
Qty:
Total:
Subtotal:
Excl. postage 
My Bag
Just added to your wishlist:
Excl. postage 
My Wishlist